Bmw Fsc Code Free Downloaded Here

The coding has been tested for a lot of times using ncs expert; its very easy.

Something interesting about BMW ENET cable E-sys software reading 1BDE file (file 1B) from BMW E or F series with CIC.

Disclaimer: Its all customer share from bmw topicsforums.

Data copied only for share info to help someone else.

Now if you open this file with hex editor, you will find the VIN of the CIC NBT (in case you did not know).

Now convert the hex file, in base 64, as in the photo.

I use the online tools).

When it is retrofit there is no Ethernet connection between OBD and CIC.

CIC must get IP address from DHCP to be accessible by ftp.

Easy way is to connect enet cable to router and restart the CIC.

This WinKFP job was after FRM3 repairreflash by Xprog like in our FRM3 repair post.

After FRM3 was repaired, then need to flash the correct software in FRM3 module.

Comfort mode and develop mode The develop flash mode you need when the FRM3 module repair dump not exacly belongs to car, and because safety reasons winkfp not leaves to update In that case You need to use winkfp develop mode, which allows to be flashed any kind of software in any module.

After spdaten is updated, then open the WinKFP and choose comfort mode and enter ZUSB (bmw zb, part number), will pop up one window where u will see the choosed zb number, accept it.

When You updating with winkfp, then need to enter the LONG vin number Then click done.

If you getting error, to cant update because software incompatibility, then need to do by DevelopExpert mode.

Now You need to copy the data file from spdaten (exxdatamodule namecoresponding data file) to winkfp develop folder (c:ec-appsnfsdatadevelop).

This is customer share about how to use BMW ICOM WinKFP to update BMW CIC module and how to generate BMW CIC NBT FSC Code with ENET cable.

PRE STEPS: In the E87 DATEN folder, make sure to swap out the file CI63F1 from the E87 Folder.

Then Load assembly line data into WINKFP (at first WINKFP should be setup for STD:OBD connection so you can do this part without having to connect to the car or ICOM).

Connect the USB cable between it and the ICOM module.

Connect OBD connector to ICOM Module.

Connect ICOM to Laptop via Ethernet cable.

Start up Itool Radar and Reserve the ICOM slot.

Youll need to search for ITool Radar).

I usually use the EasyConnect after ITOOL to select the MOST bus ASYNC setting and LOCK Icom.

Start up WINKFP and select comfort mode 7 - Select Update ZUSB 8 - From the list, select CI62F1 first and click OK.

Enter VIN 10 - Click DONE.

In Next window, Click PROG-ZUSB.

Blue bar will start - This step will take about 35-40 minutes.

Bmw Fsc Code Free Downloaded Here

Once these steps are complete, CIC will boot up again and youre done This is attaching zip files - FSC CODE Calculator Software for BMW Navigation can be free downloaded here: Pass: EintrachtFrankfurt.

BMW ENET cable 3.EDIABAS Tool32 software Following Steps: 1) READ FSC Open FSC Generator software on desktop Click Read FSC Select BMW chassis, e.g E-series Click Connect then Read VIN The software will display vehicle information Click Read FSC (1B) Click Save to File Exit.

To change the language from navigation and display to Dutch from BMW E88 2009 German import.

If the car is a German one, you can select only German, English and French from the iDrive menue.

Read CIC Edit FSWPSW.TRC ( adding or editing ) languages Copy and paste to FSWPSW.MAN Execute sgcodieren.

Bmw Fsc Code Keygen Crack